GET THE BEST RESULTS WITH THE HIGHEST QUALITY AIR COMPRESSOR OILS
GET LONGER LUBRICANT LIFE WITH LESS DOWN TIME FROM OUR AIR COMPRESSOR OILS
Keep your food-grade and non-food-grade air compressors working smoothly and efficiently with one of our industrial air compressor lubricants described below.
Rotary Screw
(FOOD GRADE STATUS: H-2)
This is a multi-grade synthetic, blended fluid for use in applications which require a 32 or 46 ISO fluid. Typical life of these fluids is 4000-6000 hours.
CAMCO® 91-40 Plus
A combination of premium synthetic and semi-synthetic fluids with a combination of premium additives. Used in applications where an improved degree of oxidative stability, higher temperature performance, low volatility and seal conditioning is required. Meets the viscosity requirements of most major screw compressor OEMs.
Formulated for extended life in flooded screw compressors, certain vacuum pump applications, and general applications where a high quality lubricant with excellent Oxidative, Rust and Corrosion inhibited product is required. Provides improved cleanliness, low foaming characteristics, good water separation and improved compatibility with elastomers and seals.
Typical drain intervals are up to four times that of conventional mineral oils rotary screw air compressors under normal operating conditions, and one year drain intervals possible. These products typically outperform competitor’s group II and III type semisynthetic compressor oils, including many that claim one year.
A lubricant analytical program is suggested to maximize the drain intervals. Life expectancy is dependent on operating and environmental conditions. Other viscosity grades and formulations are available for specific applications. These products have lower volatility than mineral oils, and have improved compatibility with systems designed for use with mineral oils.
Date: Revised 01/16
TYPICAL PROPERTIES*
| Viscosity @ 40°C cs (SSU) ASTM D445 | 42.8 |
| Viscosity @ 100°C | 6.92 |
| Viscosity Index, ASTM D2270 | 119 |
| Density, lb/gal, 77°F | 7.13 |
| Pour Point, °F | < -40 |
| Flash Point, C.O.C., °F (°C) ASTM | 469 (243) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 509 (265) |
| Foam Tendency (Seq. I, II, II) | Nil/10/5 |
| Total Acid Number (TAN) | 0.06 |
| Copper Corrosion @ 100°C ASTM D-130 | 1A |
*Mid ISO Grade at 40°C and high Viscosity Index meets most OEM requirements.
These values are not intended for use in preparing specifications
(Food Grade Status: Non-Food Grade)
These fluids are CAMCO’s premier line of high temperature, long-life fluids. They can withstand extended service at elevated discharge temperatures and may be used for many other high temperature applications including hydraulics and chain oils.
CAMCO® 42-S SERIES (42-15-S, 42-22-S)
CAMCO® 42-S Series lubricants are formulated from selected premium (advanced) type polyol ester (POE), new generation advanced modified polyol ester synthetic oils suitable for air compressors, bearings, ovens, hydraulic systems, and certain high temperature applications where good lubricity (mild ash-less anti-wear), water separation, very low carbon forming, and excellent oxidation resistance are required.
The result is maximum performance in screw air compressors! Recommended for extra long life at higher temperatures, excellent cleanliness and low oil use to keep system performance at optimum levels and reduced maintenance. Superior low temperature properties. CAMCO® 42-S Series in the ISO VG 15 and 22 are biodegradable.
* Lubricant life is dependent on operating conditions an environment
CAMCO® 42-S SERIESTYPICAL PROPERTIES *
| Viscosity | ASTM D-445 | cSt @40°C | 115.9 | 23.1 |
| Viscosity | ASTM D-445 | cSt @100°C | 3.54 | 4.65 |
| Viscosity Index | ASTM D-2270 | 101 | 118 | |
| Density 20°C | ASTM D-4052 | g/cclb/gal | 0.968.02 | 0.957.93 |
| Flash Point | ASTM D-92 | °C (°F) | 245 (473) | 240(464) |
| Fire Point | ASTM D-92 | °C (°F) | 275 (527) | 285 (545) |
| Pour Point | ASTM D-97 | °C (°F) | -66 (-87) | -63 (-81) |
*Typical properties are not meant for preparing specifications
5/17
(Food Grade Status: H-2)
This is a custom-blended polyalkylene glycol (PAG)/ester rotary screw air compressor lubricant. This is a long-life lubricant formulated with rust & oxidation inhibitors, and it will not leave behind carbon residue/varnish when it oxidizes (as compared with hydrocarbon-based products).
CAMCO® PAG 42 SERIES
CAMCO® PAG 42 Series are custom blended polyalkylene glycol (PAG)/ester rotary screw air compressor lubricants. This formulation offers improved lubrication at high and low temperatures, reduced volatility, and high viscosity index, plus excellent corrosion protection.
CAMCO® PAG 42 Series are long life lubricants formulated with rust and oxidation inhibitors. Other viscosities are available for specific applications.
CAMCO® PAG 42 Series will not leave behind carbon residue/varnish when it oxidizes as compared to hydrocarbon based products.
9/15
TYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 39.34 | 48.25 |
| Viscosity @ 100°C cs | 7.89 | 9.38 |
| Viscosity @ 100°F | 42.75 | 52.53 |
| Viscosity @ 210°F | 8.06 | 9.59 |
| Viscosity Index ASTM D2270 | 177 | 182 |
| Density, g/ml, 20°C | .974 | .974 |
| Flash Point, C.O.C., °F ASTM D92 | 510°F | 525°F |
| Fire Point, C.O.C., °F ASTM D92 | 575°F | 540°F |
| Color | Green | Water White |
| Pour Point | -51°C | -48°C |
| Copper Corrosion | la | la |
* These values are not intended for use in preparing specifications
(FOOD GRADE STATUS: H-1)
This series features air custom-blended polyalphaolefin (PAO) synthetic hydrocarbon fluids that offer improved lubrication at high and low temperatures. Other features are reduced volatility and compatibility with mineral oils. A long-life lubricant especially formulated with rust and oxidation inhibitors for flooded screw compressors.
CAMCO® FMO-32 AND FMO-46
A polyalphaolefin (PAO) synthetic fluid for Rotary Screw Air Compressors. USDA H-1 Food Grade approved.
CAMCO® FMO-32 AND FMO-46 are custom-blended polyalphaolefin (PAO) synthetic hydrocarbon oils giving improved lubrication at high and low temperatures, reduced volatility, and compatibility with mineral oils and equipment designed for use with mineral oils.
CAMCO® FMO-32 and FMO-46 are USDA H-1 Food Grade approved for use in federally inspected meat and poultry processing plants. Complies with FDA 21 CFR178.3570 – Lubricants with Incidental Food Contact.
CAMCO® FMO-32 and FMO-46 are:
- Long life lubricants
- Non shearing
- High thermal and oxidative stability
- Less lubricant carry-over
- Low foaming
- Non Carbonizing
- Excellent water separating capability
- Excellent coolants
9/12
TYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 31.4 | 46.9 |
| Viscosity @ 100°C cs | 6.0 | 7.9 |
| Viscosity at 210°F, | 6.1 | 8.13 |
| Viscosity at 100°F, | 34.3 | 51.5 |
| Viscosity Index ASTM D2270 | 140 | 139 |
| Density, lb/gal, 60°F | 6.88 | 6.91 |
| Pour Point, °F (°C) ASTM D97 | -87 (-66) | -76 (-60) |
| Flash Point, C.O.C., °F (°C) ASTM D92 (246) | 464 (240) | 475 |
| Fire Point, C.O.C., °F(°C) ASTM D92 (273) | 514 (268) | 525 |
| Specific Gravity, ASTM D1298 | 0.826 | 0.829 |
* These values are not intended for used in preparing specifications.
(FOOD GRADE STATUS: H-2)
These fluids are PAO-based with a service life of up to 8000 hours, offering many advantages over mineral oils. They have no adverse compatibility problems.
CAMCO® 41-32 & CAMCO® 41-46
A polyalphaolefin (PAO) synthetic non-food grade rotary screw compressor lubricant.
CAMCO® 41-32 and 41-46 are a custom-blended polyalphaolefin (PAO) synthetic hydrocarbon oil giving improved lubrication at high and low temperatures, reduced volatility and compatibility with mineral oils and equipment designed for use with mineral oils.
CAMCO® 41-32 and 41-46 are a long life lubricant formulated especially for flooded screw compressors. Other viscosities are available for specific applications.
9/09
CAMCO® 41-32 and CAMCO® 41-46
TYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 30.72 | 43.33 |
| Viscosity @ 100°C cs | 5.97 | 7.45 |
| Viscosity @ 100°F | 33.49 | 47.56 |
| Viscosity @ 210°F | 6.10 | 7.62 |
| Viscosity Index ASTM D2270 | 144 | 138 |
| Density, lb/gal, 60°F | 6.95 | 6.99 |
| Pour Point °F (°C) ASTM D97 | -90 (-68) | <-65 (-54) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 470 (243) | 515 (268) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 520 (271) | 535 (279) |
| Specific Gravity, ASTM D1298 | 0.835 | 0.839 |
* These values are not intended for use in preparing specifications
(FOOD GRADE STATUS: H-1)
This is a food machinery oil which is custom blended, highly-refined, and a chemically-inert lubricant series. It contains additives for improved lubricity, and features de-foaming characteristics. Widely used in applications for food processing industries in which the lubricant has indirect contact with food substances.
CAMCO® PURE SERIES FOOD GRADE CUSTOM-BLENDED LUBRICANTS
PRODUCT DESCRIPTION
CAMCO® Food Machinery Oil is a custom-blended highly refined, chemically inert lubricant series with additives for improved lubricity and defoaming characteristics. Widely used for applications in the food processing industries where the lubricant has indirect contact with food substances.
APPLICATIONS
- General purpose lubricant for long life and antiwear
- Lubricant and sealing fluid for rotary mechanical shaft seals of processing pumps and agitated kettles Lubricant/coolant for compressors
- Energy saving gear applicationsCAMCO® Food Machinery Oil meets 21 CFR178.3570 requirements for lubricants with the possibility of indirect food contact. Authorized by USDA for use in Federally inspected meat and poultry plants.
Revised 09/09
CAMCO® PURE SERIESTYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 30.49 | 47.0 | 69.1 |
| Viscosity @ 100°C cs | 5.28 | 7.0 | 9.1 |
| Viscosity @ 100°F | 33.52 | 51.7 | 77.1 |
| Viscosity @ 210F | 5.4 | 7.3 | 9.2 |
| Viscosity Index, ASTM D2270 | 105 | 100 | 100 |
| Density, lb/gal, 60°F | 7.2 | 7.2 | 7.2 |
| Flash Point, C.O.C.°F (°C), ASTM D92 (237) | 420 (216) | 425 (218) | 460 |
| Pour Point, °F (°C) | 0 (-18) | 0 (-18) | 5 (-15) |
| Fire Point, C.O.C.°F(°C) ASTM D92 (251) | 445(229) | 440 (226) | 485 |
| Specific Gravity, ASTM D1298 | 0.86 | 0.86 | 0.86 |
* These values are not intended for use in preparing specifications.
A custom-blended, PAO synthetic, 8000-hour food grade lubricant that provides two times the life of other PAO synthetic food grade oils on the market today.
CAMCO® FMO XL-46
PRODUCT DESCRIPTION
CAMCO® FMO XL-46, an 8,000 hour food grade air compressor oil, is a unique formulation derived from a blend of polyalphaolefin (PAO) synthetic lubricant and other advanced synthetic fluids and proprietary additives. The CAMCO® FMO XL-46 provides improved lubrication at high and low temperatures, reduced volatility, and compatibility with mineral oils. An advanced additive system provides superior equipment life and longer drain intervals than previously achievable with PAO's or mineral oils.
All components meet NSF H-1 requirements, where incidental food contact may occur.
The CAMCO® FMO XL-46 food grade air compressor oil has been field tested and has shown that it can last up to 2 times longer than other synthetic PAO food grade oils on the market.
APPLICATIONS
Most commonly used for compressor, light duty Hydraulic fluid, bearing and circulating systems (coolant and heat transfer) applications.
Formulated to extend life for applications requiring excellent oxidative, rust and corrosion resistance, low foaming and good water separation characteristics
8/18
CAMCO® FMO XL-46TYPICAL PROPERTIES *
| Viscosity @ 40°C cSt | 15 | 32 | 43 | 66 |
| Viscosity @ 100°F SUS | 3.8 | 6 | 7.8 | 9.6 |
| Viscosity Index | 124 | 140 | 136 | 133 |
| Density, lb/gal, | 6.81 | 6.89 | 6.93 | 6.97 |
| Specific Gravity 60/60 °F | 0.82 | 0.825 | 0.83 | 0.835 |
| Pour Point, °F (°C) | -90(-68) | <-65(-54) | -65(-54) | -65(-54) |
| Flash Point, °F (°C) | 419(215) | 464(240) | 516(268) | 516(268) |
| Demulsibility, ASTM D1401, 140°F(°C) | 40-40-0(5) | 40-40-0(5) | 40-40-0(5) | 40-40-0(5) |
| Special Heat, cp***Cal/Gm°C 100°F | 0.53 | 0.54 | 0.57 | |
| Special Heat, cp***Cal/Gm°C 200°F | 0.57 | 0.58 | 0.59 | |
| Thermal Conductivity***BTU/Hr/Ft²/°F/Ft 100°F | 0.089 | 0.091 | 0.092 | |
| Thermal Conductivity***BTU/Hr/Ft²/°F/Ft 200°F | 0.087 | 0.089 | 0.090 | |
| Shell 4-ball Wear One hour, 1200 RPM, 40 kg load 167/F, 52-100 Steel-Average Wear Spot Diameter, mm | <0.72 | <0.72 | <0.72 | <0.72 |
*** Calculated from base fluid data, values estimated.
* These values are not intended for use in preparing specifications
A unique blend of an advanced, modified POE with PAO synthetic base fluids that will, with the use of a good analytical program, result in rotary air compressor performance life of 10,000 hours or more.
CAMCO® 4642-46
PRODUCT DESCRIPTION
CAMCO® 4642-46 is a unique blend of an advanced modified polyolesters with synthetic hydrocarbon base fluids. Intended for applications which require a high degree of oxidative stability, higher viscosity index and good separation from water. Long life, good lubricity and lower varnish forming tendency result in lower maintenance costs
Formulated for extended life in flooded screw compressors and general applications where an Oxidative, Rust and Corrosion Inhibited product (R&O) with low foaming characteristics and good water separation is indicated. Other viscosities are available for specific applications. These products have lower volatility than mineral oils, and are compatible with systems designed for use with mineral oils. Extended performance over normal PAO (synthetic hydrocarbon) formulations to extend life over competitive brands by as much as 20 to 50%.
Use of a good analytical program can result in rotary air compressor performance life of 10,000 hours or more. Lubricant life is dependent on operating and environmental conditions.
Other viscosities available (also custom blend and private label available)
10/2015
CAMCO® 4642-46
TYPICAL PROPERTIES *
| Viscosity @ 40°C cSt | 49 |
| Viscosity @ 100°F cSt | 7.9 |
| Viscosity Index | 135 |
| Density 15.6°C (60°F) pounds/gallons | 7.3 |
| Flash Point, °F (°C) | 510 (265) |
| Fire Point, °F (°C) | 540 (282) |
| Pour Point, °F (°C) | -72 (-58) |
*** Calculated from base fluid data, values estimated.
* These values are not intended for use in preparing specifications
Reciprocating
(FOOD GRADE STATUS: H-2)
These fluids are manufactured from semi-synthetic base stocks with additives for anti-wear, rust, and oxidation. They have low-sludge and low varnish-forming tendencies.
A hydrotreated oil for reciprocating air compressors.
CAMCO® Compressor Oil is based on highly “semi-synthetic”, hydrotreated dewaxed iso-paraffinic oil. This special refining coupled with state-of-the-art additive technology results in performance improvements beyond conventional mineral oils and many synthetic oils. Among these are:
- Exceptional oxidative stability
- Resistance to carbon build-up and low sludging tendency
- Low evaporation loss
- Viscosity stability
- Thermal and hydrolytic stability
- Rust and corrosion inhibited maintenance
- Long Life
- Less frictional drag – Less downtime
- Improved economy
- Consistent quality
- Improved performance
- Lower equipment
9/09
Compressor Oil 68-HT
TYPICAL PROPERTIES*
| Viscosity @ 100°F, (SUS) | 366 |
| Viscosity @ 100°C, cs | 9 |
| Viscosity @ 40°C, cs | 70 |
| Viscosity Index ASTM D2270 | 107 |
| Pour Point, °F (°C) | -22 (-30) |
| Flash Point, C.O.C., °F, (°C), ASTM D92 | 141 (230) |
| Fire Point, C.O.C., °F, (°C), ASTM D92 | 490 (2724) |
| Rust Procecure 48 hours, ASTM D665 | Pass |
| Mechanical Emulsion @ °F(54°C) ASTM D1401 Ml Oil/Ml Water/Ml Emulsion (time) | 42-38-0(20) |
| Ramsbottom Carbon Residue ASTM D524 | 0.27 |
| Conradson Carbon Residue ASTM D189 | 0.03 |
| Shell 4-Ball wear - 40Kg, 1 hour, 54.4°C, 52100 steel, 1,800 RPM, wear scar mm ASTM D4172 | 0.48 |
| Foaming characteristics ASTM D892 - Sequence 1 | 5/0 |
| Foaming characteristics ASTM D892 - Sequence 2 | 15/0 |
| Foaming characteristics ASTM D892 - Sequence 3 | 0/0 |
| Air Release at 50°C, minutes | 10.7 |
| Color, ASTM D1500 | 0.5 |
| Weight Pounds/Gallon 60°F (15°C) | 7.2 |
| Total Acid Number | 0.85 |
| Analine Point °F (°C) ASTM D611 | 280 (137.5) |
| Copper Corrosion ASTM D130 3 hour, 121°C | 1 |
| Rotary Bomb Oxidation, Mins. ASTM D2272 | 255 Pass |
| Oxidation stability, 24 hr. IP48 | |
| Evaporation wt. Loss, % | 5.0 |
| Conradson Carbon Increase | 0.03 |
| CSt at 40°C, % Increase | 22 |
| Pneurop Conradson Carbon Increase DIN1352-2 | 0.42 |
These values are not intended for preparing specifications.
Compressor Oil 100-HT
TYPICAL PROPERTIES *
| Viscosity @ 100°F, (SUS) | 571 |
| Viscosity @ 100°C, cs | 12.1 |
| Viscosity @ 40°C, cs | 109 |
| Viscosity Index ASTM D2270 | 100 |
| Pour Point, °F (°C) | -5 (-21) |
| Flash Point, C.O.C., °F, (°C), ASTM D92 | 475 (246) |
| Fire Point, C.O.C., °F, (°C), ASTM D92 | 545 (284) |
| Rust Procecure 48 hours, ASTM D665 | Pass |
| Mechanical Emulsion @ °F(54°C) ASTM D1401 Ml Oil/Ml Water/Ml Emulsion (time) | 40-36-4(30) |
| Ramsbottom Carbon Residue ASTM D524 | 0.27 |
| Conradson Carbon Residue ASTM D189 | 0.03 |
| Shell 4-Ball wear - 40Kg, 1 hour, 54.4°C, 52100 steel, 1,800 RPM, wear scar mm ASTM D4172 | 0.48 |
| Foaming characteristics ASTM D892 - Sequence 1 | 0/0 |
| Foaming characteristics ASTM D892 - Sequence 2 | 15/0 |
| Foaming characteristics ASTM D892 - Sequence 3 | 0/0 |
| Air Release at 50°C, minutes | 6.7 |
| Color, ASTM D1500 | 0.5 |
| Weight Pounds/Gallon 60°F (15°C) | 7.3 |
| Total Acid Number | 0.88 |
| Analine Point °F (°C) ASTM D611 | 288 (142) |
| Copper Corrosion ASTM D130 3 hour, 121°C | 1 |
| Rotary Bomb Oxidation, Mins. ASTM D2272 | 260 Pass |
| Oxidation stability, 24 hr. IP48 | |
| Evaporation wt. Loss, % | 2.4 |
| Conradson Carbon Increase | 0.03 |
| CSt at 40°C, % Increase | 25 |
| Pneurop Conradson Carbon Increase DIN1352-2 | 0.43 |
These values are not intended for preparing specifications.
Compressor Oil 150-HT
TYPICAL PROPERTIES *
| Viscosity @ 100°F, (SUS) | 814 |
| Viscosity @ 100°C, cs | 15.40 |
| Viscosity @ 40°C, cs | 155 |
| Viscosity Index ASTM D2270 | 100 |
| Pour Point, °F (°C) | -5 (-15) |
| Flash Point, C.O.C., °F, (°C), ASTM D92 | 480 (250) |
| Fire Point, C.O.C., °F, (°C), ASTM D92 | 565 (296) |
| Rust Procecure 48 hours, ASTM D665 | Pass |
| Mechanical Emulsion @ °F(54°C) ASTM D1401 Ml Oil/Ml Water/Ml Emulsion (time) | 38-29-13(30) |
| Ramsbottom Carbon Residue ASTM D524 | 0.27 |
| Conradson Carbon Residue ASTM D189 | 0.24 |
| Shell 4-Ball wear - 40Kg, 1 hour, 54.4°C, 52100 steel, 1,800 RPM, wear scar mm ASTM D4172 | 0.45 |
| Foaming characteristics ASTM D892 - Sequence 1 | 0/0 |
| Foaming characteristics ASTM D892 - Sequence 2 | 50/0 |
| Foaming characteristics ASTM D892 - Sequence 3 | 0/0 |
| Air Release at 50°C, minutes | 10.8 |
| Color, ASTM D1500 | 0.5 |
| Weight Pounds/Gallon 60°F (15°C) | 7.31 |
| Total Acid Number | 0.87 |
| Analine Point °F (°C) ASTM D611 | 296(146.9) |
| Copper Corrosion ASTM D130 3 hour, 121°C | 1 |
| Rotary Bomb Oxidation, Mins. ASTM D2272 | Pass |
| Oxidation stability, 24 hr. IP48 | |
| Conradson Carbon Increase | 0.03 |
| CSt at 40°C, % Increase | 15 |
| Pneurop Conradson Carbon Increase DIN1352-2 | 0.56 |
These values are not intended for preparing specifications.
(FOOD GRADE STATUS: NON-FOOD GRADE)
Formulated with diester base stocks, these fluids are suitable for high-temperature reciprocating applications because they do not form solid deposits or varnish on discharge valves.
DESCRIPTION:
A synthetic ester fluid/lubricant for general purpose, bearings, compressors and other applications requiring protection from rust and oxidization and excellent cleanliness over a wide operating range. Diesters and triesters have very low deposit forming characteristics for better efficiency and cleaner operation. Longer drain intervals result from good oxidative stability.
Typical Compressor Applications include: Air, Nitrogen, Carbon Dioxide, Carbon Monoxide, Helium, Methane, Ethane, Propane, Dry Hydrogen Sulfide, and Sulfur Hexafluoride.
Many applications that call for a thermally and oxidatively stable oil will have the following benefits from the CAMCO 410 Series fluids: Extended lubricant life, clean operation, less maintenance, less oil consumption through high separation efficiency, good water separation characteristics and good lubricity.
RECOMMENDED MATERIALS - Viton, High Nitrile Buna N, Teflon, Epoxy Paint, Oil-Resistant Alkyd, Nylon, Delrin, Celcon, PBT
NOT RECOMMENDED MATERIALS - Neoprene, SBR Rubber, Low Nitrile Buna N, Acrylic Paint, Lacquer, Polystyrene, PVC, ABS
7/15
TYPICAL PROPERTIES*
| Viscosity @ 40°C | ASTM D445 | cSt | 68 | 102 | 142 |
| Viscosity @ 100°C | ASTM D445 | cSt | 8.26 | 10.18 | 11.7 |
| Viscosity Index | ASTM D2270 | 88 | 78 | 66 | |
| Density 20°C | ASTM D4052 |
g/cm3 lbs/gallon |
0.974 8.11 |
0.981 8.19 |
0.954 7.96 |
| Flash Point | ASTM D92 | °C (°F) | 265 (509) | 260 (500) | 260 (500) |
| Fire Point | ASTM D92 | °C (°F) | 285 (545) | 295 (563) | 295 (563) |
| Autoignition | ASTM E659 | °C (°F) | 405 (760) | 410 (770) | 410 (770) |
| Pour Point | ASTM D97 | °C (°F) | -42 (-44) | -36 (-33) | -39 (-38) |
| Total Acid Number | ASTM D974 | mg KOH/g | < 0.2 | < 0.2 | < 0.2 |
| Copper Strip Corrosion 3 hours @ 100°C | ASTM D130 | 1A | 1A | 1A | |
| Conradson Carbon | ASTM D189 | Residue, Wt. % | 0.02 | 0.02 | 0.02 |
| Evaporation Loss 22 hrs. @ 99°C (210°F) | ASTM D972 | % | <1 | <1 | <1 |
| 4 Ball Wear 1200 rpm, 75°C, 40 kg, 1 hr | ASTM D4172 | mm | 0.75 | 0.75 | 0.7 |
| Foam Tendency, Seq. II | ASTM D892 | ml | trace | trace | trace |
| Demulsibility 54°C (130°F) | ASTM D1404 | ml oil-water-emulsion (minutes) | 40-37-3(15) | 39/38/3(<60) | 58/22/0(<60) |
These values are not intended for use in preparing specifications
(Food Grade Status: H-1)
A polyalphaolefin (PAO) food grade hydraulic, gear, reciprocating air compressor oil.
PRODUCT DESCRIPTION
CAMCO® FMO-8 Series are high quality performance H-1 NSF food grade gear and bearing oils. The CAMCO FMO 8 Series has excellent thermal and oxidative stability providing reliable performance and extending oil life in severe applications. Minimal deposit formation gives a cleaner system and reduced frequency of filter changes.
CAMCO FMO 8 Series are custom-blended polyalphaolefin (PAO) synthetic hydrocarbon oils giving improved lubrication at high and low temperatures, reduced volatility and compatibility with mineral oils and equipment designed for use with mineral oils. Excellent shear stability, as the synthetic requires no VI improvers producing no excessive loss in viscosity due to mechanical shearing. Good antiwear properties promote reduced downtime due to unscheduled maintenance and savings from reduced replacement part costs.
Excellent water separation and hydrolytic stability mean reduced downtime through prolonged lubricant life and increased equipment reliability.
Authorized by USDA for use in Federally inspected meat and poultry plants. Complies with FDA 21CFR 178.3570 – Lubricants with Incidental Food Contact.
CAMCO® FMO-8-SERIES --- TYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 31.4 | 46.9 | 68.5 |
| Viscosity @ 100°C cs | 6.0 | 7.9 | 10.4 |
| Viscosity @ 100°F | 34.3 | 51.5 | 75.7 |
| Viscosity @ 210°F | 6.1 | 8.1 | 10.7 |
| Viscosity Index ASTM D2270 | 140 | 139 | 140 |
| Pour Point °F (°C) ASTM D97 | -87 (-66) | -76 (-60) | -60 (-51) |
| Flash Point, C.O.C., °F (°C) | 464(240) | 514(268) | 519(268) |
| Fire Point, C.O.C., °F (°C) | 514(268) | 554(290) | 568(298) |
| Specfic Gravity, ASTM D1298 | 0.826 | 0.829 | 0.835 |
| Demulsibility, 10 minutes | 40-39-1 | -- | 40-39-1 |
| Pump Wear, total ring & vane Weight loss, mg. ASTM 28810 | 10 | -- | 10 |
| Foam Test, ASTM D892, Sequence I, II, III | Nil | -- | Nil |
| Rust Prevention, ASTM D665, Distilled water | Pass | -- | Pass |
| Copper Strip Corrosion, three hrs. @ 212°F, ASTM D130 | 1 | -- | 1 |
*These values are not intended for use in preparing specifications.
CAMCO® FMO-8-SERIES --- TYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 100.3 | 147.7 | 217.4 |
| Viscosity @ 100°C cs | 13.7 | 18.2 | 24.4 |
| Viscosity @ 100°F | 111.4 | 164.8 | 243.61 |
| Viscosity @ 210°F | 14.1 | 18.7 | 25.12 |
| Viscosity Index ASTM D2270 | 138 | 138 | 141 |
| Pour Point °F (°C) ASTM D97 | -55 (-52) | -49 (-45) | -46 (-43) |
| Flash Point, C.O.C., °F (°C) | 521 (271) | 530(277) | 535 (279) |
| Fire Point, C.O.C., °F (°C) | 574 (301) | 580(304) | 585 (307) |
| Specfic Gravity, ASTM D1298 | 0.839 | 0.845 | 0.846 |
| Demulsibility, 10 minutes | 40-39-1 | -- | 40-39-1 |
| Pump Wear, total ring & vane Weight loss, mg. ASTM 28810 | 10 | -- | 10 |
| Foam Test, ASTM D892, Sequence I, II, III | Nil | -- | Nil |
| Rust Prevention, ASTM D665, Distilled water | Pass | -- | Pass |
| Copper Strip Corrosion, three hrs. @ 212°F, ASTM D130 | 1 | -- | 1 |
*These values are not intended for use in preparing specifications.
CAMCO® FMO-8-SERIES --- TYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 320.0 | 392.0 |
| Viscosity @ 100°C cs | 33.0 | 38.8 |
| Viscosity @ 100°F | 359.9 | 441.6 |
| Viscosity @ 210°F | 34.0 | 40.0 |
| Viscosity Index ASTM D2270 | 145 | 147 |
| Pour Point °F (°C) ASTM D97 | -38 (-39) | -35(-37) |
| Flash Point, C.O.C., °F (°C) | 540 (282) | 545(285) |
| Fire Point, C.O.C., °F (°C) | 592 (311) | 595(313) |
| Specfic Gravity, ASTM D1298 | 0.850 | 0.852 |
*These values are not intended for use in preparing specifications.
(Food Grade Status: H-1)
CAMCO® Pure AW Hydraulic Series
CAMCO® Pure AW Hydraulic Series are custom blended highly refined chemically inert lubricants with additives for improved lubricity and defoaming characteristics. Additives include anti-wear for use in hydraulic systems and other applications where an anti-wear lubricant is desired.
Widely used for applications in the food processing industry where the lubricant has indirect contact with food substances.
Applications
- General purpose lubricant for long life and anti-wear
- Lubricant and sealing fluid for rotary mechanical shaft seals of processing pumps and agitated kettles
- Lubricant/coolant for compressors
- Energy saving gear applications
- Hydraulic systems including fork lift trucks
CAMCO® Pure AW Series lubricants meet 21 CFR178.3570 requirements for lubricants with the possibility of indirect food contact. Authorized by USDA for use in Federally inspected meat and poultry plants for incidental food contact (H-1).
09/16
CAMCO® PURE AW SERIES TYPICAL PROPERTIES *
| @ 100°C cs | 5.7 | 6.5 | 9.0 | 12.0 | 14.9 |
| @ 40°C cs | 35.0 | 43.0 | 68.0 | 105.0 | 130.0 |
| Viscosity Index | 103 | 101 | 104 | 104 | 115 |
| Pour Point °F | -49 | -49 | -33 | -22 | -6 |
| Flash Point C.O.C. °F ASTM D92 | 410 | 432 | 450 | 491 | 485 |
| Weight lb/gal 77°F | 7.19 | 7.21 | 7.23 | 7.23 | 7.2 |
*These values are not intended for use in preparing specifications.
(Food Grade Status: H-2)
These fluids are PAO-based and have a service life of up to 8000 hours. They offer many advantages over mineral oils and have no adverse compatibility problems.
CAMCO 41 series are custom-blended polyalphaolefin (PAO) synthetic hydrocarbon fluids giving improved lubrication at high and low temperatures, reduced volatility, and compatibility with mineral oils and equipment designed for use with mineral oils. CAMCO 41 Series are long life lubricants formulated with rust and oxidation inhibitors. CAMCO 41 Series are authorized by USDA for the use in federally inspected meat and poulty plants with no possibility of food contact (H-2).
TYPICAL PROPERTIES*
| Viscosity @ 40°C cs ASTM D445 | 6.94 | 17 | 30.72 | 43.33 |
| Viscosity @ 100°C cs | 2.41 | 3.8 | 5.97 | 7.45 |
| Viscosity @ 100°F | 7.32 | 18.2 | 33.49 | 47.56 |
| Viscosity @ 210°F | 2.45 | 3.9 | 6.1 | 7.62 |
| Viscosity Index ASTM D2270 | 202 | 123 | 144 | 138 |
| Density, lb/gal, 60°F | 6.76 | 6.82 | 6.95 | 6.99 |
| Pour Point °F (°C) ASTM D97 | -100 (-73) | -100 (-73) | -90 (-68) | <-65 (-54) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 330 (165) | 425 (210) | 470 (243) | 515 (268) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 350 (176) | 480 (249) | 520 (271) | 535 (279) |
| Specific Gravity, ASTM D1298 | 0.812 | 0.82 | 0.835 | 0.839 |
| Viscosity @ 40°C cs ASTM D445 | 61.8 | 98.32 | 161.62 | 220.18 |
| Viscosity @ 100°C cs | 8.95 | 14 | 20.11 | 24.75 |
| Viscosity @ 100°F | 60 | 504 | 834 | 1142 |
| Viscosity @ 210°F | 9.17 | 75.4 | 101.2 | 122.1 |
| Viscosity Index ASTM D2270 | 121 | 145 | 144 | 141 |
| Density, lb/gal, 60°F | 7.01 | 7.02 | 7.07 | 7.06 |
| Pour Point °F (°C) ASTM D97 | -65 (-54) | -55 (-48) | -55 (48) | -30 (34) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 520 (271) | 520 | 520 (271) | 520 (271) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 580 (304) | 550 | 585 (307) | 565 (296) |
| Specific Gravity, ASTM D1298 | 0.842 | 0.843 | 0.849 | 0.848 |
These values are not intended for preparing specifications.
Centrifugal
(Food Grade Status: H-2)
This series features fluids that are PAO-based with a service life of up to 8000 hours. These fluids offer many advantages over mineral oils and have no adverse compatibility problems.
TYPICAL PROPERTIES*
| Viscosity @ 40°C cs ASTM D445 | 6.94 | 17 | 30.72 | 43.33 |
| Viscosity @ 100°C cs | 2.41 | 3.8 | 5.97 | 7.45 |
| Viscosity @ 100°F | 7.32 | 18.2 | 33.49 | 47.56 |
| Viscosity @ 210°F | 2.45 | 3.9 | 6.1 | 7.62 |
| Viscosity Index ASTM D2270 | 202 | 123 | 144 | 138 |
| Density, lb/gal, 60°F | 6.76 | 6.82 | 6.95 | 6.99 |
| Pour Point °F (°C) ASTM D97 | -100 (-73) | -100 (-73) | -90 (-68) | <-65 (-54) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 330 (165) | 425 (210) | 470 (243) | 515 (268) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 350 (176) | 480 (249) | 520 (271) | 535 (279) |
| Specific Gravity, ASTM D1298 | 0.812 | 0.82 | 0.835 | 0.839 |
| Viscosity @ 40°C cs ASTM D445 | 61.8 | 98.32 | 161.62 | 220.18 |
| Viscosity @ 100°C cs | 8.95 | 14 | 20.11 | 24.75 |
| Viscosity @ 100°F | 60 | 504 | 834 | 1142 |
| Viscosity @ 210°F | 9.17 | 75.4 | 101.2 | 122.1 |
| Viscosity Index ASTM D2270 | 121 | 145 | 144 | 141 |
| Density, lb/gal, 60°F | 7.01 | 7.02 | 7.07 | 7.06 |
| Pour Point °F (°C) ASTM D97 | -65 (-54) | -55 (-48) | -55 (48) | -30 (34) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 520 (271) | 520 | 520 (271) | 520 (271) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 580 (304) | 550 | 585 (307) | 565 (296) |
| Specific Gravity, ASTM D1298 | 0.842 | 0.843 | 0.849 | 0.848 |
These values are not intended for preparing specifications.
(Food Grade Status: H-1)
CAMCO® FMO Series
A polyalphaolefin (PAO) synthetic fluid for Rotary Screw Air Compressors. USDA H-1 Food Grade approved.
CAMCO® FMO Series are custom-blended polyalphaolefin (PAO) synthetic hydrocarbon oils giving improved lubrication at high and low temperatures, reduced volatility, and compatibility with mineral oils and equipment designed for use with mineral oils.
CAMCO® FMO Series are USDA H-1 Food Grade approved for use in federally inspected meat and poultry processing plants. Complies with FDA 21 CFR178.3570 – Lubricants with Incidental Food Contact.
CAMCO® FMO Series are:
- Long life lubricants
- Non shearing
- High thermal and oxidative stability
- Less lubricant carry-over
- Low foaming
- Non Carbonizing
- Excellent water separating capability
- Excellent coolants
TYPICAL PROPERTIES *
| Viscosity® 40°C cs ASTM D445 | 31.4 | 46.9 |
| Viscosity® 100°C cs | 6.0 | 7.9 |
| Viscosity at 210°F, | 6.1 | 8.13 |
| Viscosity at 100°F, | 34.3 | 51.5 |
| Viscosity Index ASTM D2270 | 140 | 139 |
| Density, lb/gal, 60°F | 6.88 | 6.91 |
| Pour Point, °F (°C) ASTM D97 | -87 (-66) | -76 (-60) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 464 (240) | 475 (246) |
| Fire Point, C.O.C., °F(°C) ASTM D92 | 514 (268) | 525 (273) |
| Specific Gravity, ASTM D1298 | 0.826 | 0.829 |
* These values are not intended for used in preparing specifications.
TYPICAL PROPERTIES *
| Viscosity® 100°C cs ASTM D445 | 10.4 | 13.7 |
| Viscosity® 40°C cs | 68.5 | 100.3 |
| Viscosity® 100°F | 75.7 | 111.4 |
| Viscosity® 210°F | 10.7 | 14.1 |
| Viscosity Index, ASTM D2270 | 140 | 138 |
| Density, lb/gal, 60°F | 6.96 | 6.99 |
| Pour Point °F (°C) ASTM D97 | -60 (51) | -55 (-52) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 519 (268) | 521 (271) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 568 (298) | 574 (301) |
| Specific Gravity, ASTM D1298 | 0.835 | 0.839 |
* These values are not intended for use in preparing specifications.
(FOOD GRADE STATUS: H-2)
This is a multi-grade synthetic, blended fluid for use in applications which require a 32 or 46 ISO fluid. Typical life of these fluids is 4000-6000 hours.
CAMCO® 91-40 Plus
A combination of premium synthetic and semi-synthetic fluids with a combination of premium additives. Used in applications where an improved degree of oxidative stability, higher temperature performance, low volatility and seal conditioning is required. Meets the viscosity requirements of most major screw compressor OEMs.
Formulated for extended life in flooded screw compressors, certain vacuum pump applications, and general applications where a high quality lubricant with excellent Oxidative, Rust and Corrosion inhibited product is required. Provides improved cleanliness, low foaming characteristics, good water separation and improved compatibility with elastomers and seals.
Typical drain intervals are up to four times that of conventional mineral oils rotary screw air compressors under normal operating conditions, and one year drain intervals possible. These products typically outperform competitor’s group II and III type semisynthetic compressor oils, including many that claim one year.
A lubricant analytical program is suggested to maximize the drain intervals. Life expectancy is dependent on operating and environmental conditions. Other viscosity grades and formulations are available for specific applications. These products have lower volatility than mineral oils, and have improved compatibility with systems designed for use with mineral oils.
Date: Revised 01/16
TYPICAL PROPERTIES*
| Viscosity @ 40°C cs (SSU) ASTM D445 | 42.8 |
| Viscosity @ 100°C | 6.92 |
| Viscosity Index, ASTM D2270 | 119 |
| Density, lb/gal, 77°F | 7.13 |
| Pour Point, °F | < -40 |
| Flash Point, C.O.C., °F (°C) ASTM | 469 (243) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 509 (265) |
| Foam Tendency (Seq. I, II, II) | Nil/10/5 |
| Total Acid Number (TAN) | 0.06 |
| Copper Corrosion @ 100°C ASTM D-130 | 1A |
*Mid ISO Grade at 40°C and high Viscosity Index meets most OEM requirements.
These values are not intended for use in preparing specifications
(FOOD GRADE STATUS: H-1)
This is a food machinery oil which is custom blended, highly-refined, and a chemically-inert lubricant series. It contains additives for improved lubricity, and features de-foaming characteristics. Widely used in applications for food processing industries in which the lubricant has indirect contact with food substances.
CAMCO® PURE SERIES FOOD GRADE CUSTOM-BLENDED LUBRICANTS
PRODUCT DESCRIPTION
CAMCO® Food Machinery Oil is a custom-blended highly refined, chemically inert lubricant series with additives for improved lubricity and defoaming characteristics. Widely used for applications in the food processing industries where the lubricant has indirect contact with food substances.
APPLICATIONS
- General purpose lubricant for long life and antiwear
- Lubricant and sealing fluid for rotary mechanical shaft seals of processing pumps and agitated kettles Lubricant/coolant for compressors
- Energy saving gear applicationsCAMCO® Food Machinery Oil meets 21 CFR178.3570 requirements for lubricants with the possibility of indirect food contact. Authorized by USDA for use in Federally inspected meat and poultry plants.
Revised 09/09
CAMCO® PURE SERIESTYPICAL PROPERTIES *
| Viscosity @ 40°C cs ASTM D445 | 30.49 | 47.0 | 69.1 |
| Viscosity @ 100°C cs | 5.28 | 7.0 | 9.1 |
| Viscosity @ 100°F | 33.52 | 51.7 | 77.1 |
| Viscosity @ 210F | 5.4 | 7.3 | 9.2 |
| Viscosity Index, ASTM D2270 | 105 | 100 | 100 |
| Density, lb/gal, 60°F | 7.2 | 7.2 | 7.2 |
| Flash Point, C.O.C.°F (°C), ASTM D92 (237) | 420 (216) | 425 (218) | 460 |
| Pour Point, °F (°C) | 0 (-18) | 0 (-18) | 5 (-15) |
| Fire Point, C.O.C.°F(°C) ASTM D92 (251) | 445(229) | 440 (226) | 485 |
| Specific Gravity, ASTM D1298 | 0.86 | 0.86 | 0.86 |
* These values are not intended for use in preparing specifications.
Call us at (763) 205-0828 to order.
(Food Grade Status: H-1)
CAMCO® FMO Series
A polyalphaolefin (PAO) synthetic fluid for Rotary Screw Air Compressors. USDA H-1 Food Grade approved.
CAMCO® FMO Series are custom-blended polyalphaolefin (PAO) synthetic hydrocarbon oils giving improved lubrication at high and low temperatures, reduced volatility, and compatibility with mineral oils and equipment designed for use with mineral oils.
CAMCO® FMO Series are USDA H-1 Food Grade approved for use in federally inspected meat and poultry processing plants. Complies with FDA 21 CFR178.3570 – Lubricants with Incidental Food Contact.
CAMCO® FMO Series are:
- Long life lubricants
- Non shearing
- High thermal and oxidative stability
- Less lubricant carry-over
- Low foaming
- Non Carbonizing
- Excellent water separating capability
- Excellent coolants
TYPICAL PROPERTIES *
| Viscosity® 40°C cs ASTM D445 | 31.4 | 46.9 |
| Viscosity® 100°C cs | 6.0 | 7.9 |
| Viscosity at 210°F, | 6.1 | 8.13 |
| Viscosity at 100°F, | 34.3 | 51.5 |
| Viscosity Index ASTM D2270 | 140 | 139 |
| Density, lb/gal, 60°F | 6.88 | 6.91 |
| Pour Point, °F (°C) ASTM D97 | -87 (-66) | -76 (-60) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 464 (240) | 475 (246) |
| Fire Point, C.O.C., °F(°C) ASTM D92 | 514 (268) | 525 (273) |
| Specific Gravity, ASTM D1298 | 0.826 | 0.829 |
* These values are not intended for used in preparing specifications.
TYPICAL PROPERTIES *
| Viscosity® 100°C cs ASTM D445 | 10.4 | 13.7 |
| Viscosity® 40°C cs | 68.5 | 100.3 |
| Viscosity® 100°F | 75.7 | 111.4 |
| Viscosity® 210°F | 10.7 | 14.1 |
| Viscosity Index, ASTM D2270 | 140 | 138 |
| Density, lb/gal, 60°F | 6.96 | 6.99 |
| Pour Point °F (°C) ASTM D97 | -60 (51) | -55 (-52) |
| Flash Point, C.O.C., °F (°C) ASTM D92 | 519 (268) | 521 (271) |
| Fire Point, C.O.C., °F (°C) ASTM D92 | 568 (298) | 574 (301) |
| Specific Gravity, ASTM D1298 | 0.835 | 0.839 |
* These values are not intended for use in preparing specifications.